Normal household timers are not built to take the high inductive loads produced by HID ballasts. If used with a HID ballast, the contacts inside the timer that open and close the timed circuit will overheat and weld together, breaking the timer and leaving your grow lights permanently on.

Suitable for timing on 600w HID ballasts

Cables sold separately

Exclusive at Microfluo !

Ultra Compact Clock Horti Gear 600 Watt HPS / MH.

The most efficient on the market. See comparative test on our blog

Dimensions: 280x 125 x 120mm
Weight : 7.1Kg

Also available in 150W, 250W and 400W

Important note:
Class 1 ballasts are delivered uncabled.

Sockets and cables also available from Microfluo

Large choice of MH and HPS bulb 600 Watt

More important notes :

-Protect from humidity and water

-Do not directly put it on the ground

-Let it cool down before moving it / picking it up

-The used lamps must be of identical power

The installation of this product has to be done by a qualified electrician.

Hammertone reflector aluminum 47 Cm with Socket E40

Accepts all bulbs with E40 socket:

•   Bulbs HPS (High Pressure Sodium) 250 400 600 and 1000 watts.
•   MH bulbs (Metal Halide) 250 400 600 and 1000 watts.

- Reflector dimensions: 47cm long x 47cm wide x 11.5 maximum height.

AC input 230v / 50hz / 250-1000w

wiring not supplied

Hanger PROHANGER Regular

Used to hang objects like leds and filters, 2 pieces per box.

Maximum weight : 48kg (2x24kg)

Maximum length : 150cm

This product is designed for the suspension in culture chambers, for the lighting that allows flowering. It's also used to hang carbon filters.

Height adjustment is possible and easy.

The carabiners are resistant, made of steel. The strings are made of nylon, a flexible and easy to handle material.

CEE 7/7 - 3G 1.5 (2m)

Power cable with CEE 7/7 male plug, 2 meters long.

Used for connections to your ballasts, extractors or reflectors for CFL lamps.

Sold by meter

Flexible electric cable 3x2.5mm²

Sold by meter

ø 150mm

520m³/h

APPLICATION
The VENTS TT fans are featured with wide capabilities and high performance of axial and centrifugal fans and are specifically designed for supply and exhaust ventilation of premises requiring high pressure, powerful air flow and low noise level.	The fans are compatible with round air ducts from Ø 100 to 315 mm. Exhaust ventilation systems based on the VENTS TT fans are the best solution for ventilation of bathrooms and kitchens and other humid premises as well for ventilation of flats, cottages, shops, cafes, etc.
DESIGN
The casing is made of high-quality durable plastic.	All the models may be equipped with a regulated timer with turn-off delay adjustable from 2 to 30 min.
The removable impeller and motor block with a terminal box is fixed to the casing assembled with the spigots by means of special clamps with latches. This makes the fan maintenance fast and easy. The fan maintenance does not require total disassembling. Just pull out the central block from the casing and perform required servicing.
MOTOR
The models of VENTS TT series are equipped with a single phase motor and are available in single or two speed modifications. Some dimension types are available with a more powerful motor (VENTS TT…S). The motors have thermal overheating protection to prevent the motor overload.	The ball bearings extend the motor service life up to 40 000 hrs. at non-stop operation. The motor has IP X4 ingress protection rating.
SPEED CONTROL
The double-speed motors are controlled with a built-in switch (V option) or an external switch for multi-speed fans (available upon separate order).	An integrated speed controller (option P), an external TRIAC or autotransformer speed controller (available upon separate order) are used for smooth speed control when connected to the maximum speed terminal.
MOUNTING
The fans are suitable for mounting at any angle and point of the system. Several fans may be installed inside one system.  Several fans may be installed inside one system: parallel mounting to increase air flow; in series mounting to increase operating pressure;	The fan case is equipped with a flat mounting plate to attach the fan to the wall. The mounting box may be installed in any position to facilitate mounting and wiring.
THE FAN WITH ELECTRONIC MODULE OF THE TEMPERATURE SENSOR AND SPEED CONTROLLER (U OPTION)
The ideal solution for ventilation of the premises with high demands to permanent indoor temperature level, e.g. greenhouses. The fan with the electronic module of the temperature sensor and the speed controller is used for automatic speed control (air capacity regulation) depending on the air temperature in the ventilation duct or inside a room. Two modifications are possible: temperature sensor integrated inside a fan duct (U/U1 option) external temperature sensor fixed on 4 m power cable (Un / U1n option)	The electronic module of the front panel incorporates: the speed control knob for the setting the impeller speed; the thermostat control knob for setting the temperature set point.  thermostat LED light.
OPERATING LOGIC OF THE FAN WITH THE ELECTRONIC MODULE OF THE TEMPERATURE SENSOR AND SPEED CONTROLLER
Set the desired air temperature (set point of the thermostat) with the thermostat control knob. Set the required minimum impeller speed (air flow) with the speed control knob. The motor switches to maximum speed (maximum air flow) as the temperature reaches and exceeds the set temperature set point. The motor switches to the pre-set speed as the temperature drops down below the set temperature point.	To avoid the frequent motor switching, e.g. when the temperature in the supply air duct is equal to the threshold value, the switching delay time is activated.
There are two switch delay patterns for various cases:
The temperature sensor-based switch delay (U option): the motor switches to higher speed as the air temperature exceeds 2°C above the set thermostat set point. The motor revers to the pre-set lower speed as the air temperature drops below the thermostat set point. This pattern is used to keep air temperature to within 2°C. In this case the fan switches are rare.	The timer-based switch delay (U1 option): as the air temperature exceeds the set thermostat set point, the motor switches to higher speed and the switch delay timer is activated for 5 min. The motor reverts to lower speed as the air temperature drops down below the thermostat set point and only after the timer countdown.This pattern is used for exact air temperature control. The fan changes its speed more often as compared to the temperature sensor-based switch delay, however the minimum timer interval is 5 minutes.
TT FANS APPLICATIONS
bathroom ventilation example	office ventilation example
parallel installation of fans in the storehouse to increase the air capacity

Clamp with clamping screw in galvanized steel.

Diameter : 60-165mm

Ducting clip's width : 6mm

Ideal for ventilation ducts connections.

Adaptable on all ducts, extractors or filters of the same diameter available in our stock. The tightening is done with a screw.

This ducting clip is able to bring together 2 round parts with a diameter between 60 and 165mm.

The ducting clip is made of stainless steel: This material is corrosion resistant, durable and adapts well to temperature changes.

This object can be useful in all circumstances ; Gardening, plumbing,... It can be used indoors and outdoors.

Discover more duting clips on our website !

600-660m³/h

150mm Ø

Can-Lite 600 steel filter with a capacity of 600 to 660m3.

Flange 150mm

Also available in 160mm

Its size is 47.5cm in length and 20 cm in diameter.

It is characterized by a very light weight (4kg)

We recommend this filter with our extractors TT150, VK150 as well as with Alubox 550m3 for example.

Oscillating clip fan

Oscillating Clip Fan "Monkey" 

‎

Size : 20cm

Weight : 1kg

Diameter : 23cm

Power : 20 watt

Voltage : 220V

Colour : White

Rotation speed : 1500-2300 rpm

Has 2 speeds.

‎

This product, with its advantageous size and weight, makes the air circulate well in tents and grow rooms, while remaining silent.

Thanks to its clip, you can hang it anywhere. Thanks to its small size, it's not difficult to find a place for it. In addition, the fan can be slightly bent down so that it can aim the desired location.

It can grip on bars between 16cm and 21cm wide. The clamp is strong and will not make the fan fall on your plants.

The motor is made of copper : This prevents the product from overheating so it has a longer life, saves energy and makes it quieter.

Thanks to its 2 speeds, you can control the flow of air.

Cable length 150cm.

‎

Find more oscillating clipfans on our website !

Themometer - Hygrometer, min/max

PROHYGRO HYGROTHERMO PREMIUM

Thermometer / Hygrometer

‎‎

Dimensions: 11.5x6x1.2

Screen size:  4x4cm

Min / max temperature range: 0° C - 50° C (32° F - 122° F)

Accuracy: ± 1° C / RH ± 5% relative humidity

‎Internal hygro capacity: 25% / RH 90%

‎

Thanks to this device, you will be able to measure the humidity rate and the ambient air of the place where you will put it. It is possible to place it in a horticultural environment (greenhouses) as well as in a domestic environment. It can be placed against a wall or placed on a straight surface.

In addition, this thermometer-hygrometer is able to save the recorded data. Its min / max memory function allows you to see the maximum and minimum temperatures that were recorded throughout the day.

It has an LCD screen. LCD screens are durable and have a reasonable price.

There is the possibility of changing Celsius to Fahrenheit, and vice versa.

‎

You can find a wider choice of hygrometer thermometers on our website !

11l fabric pot

Promotes optimal root health

22x22x24cm

New Gold Label Fabric Pots, meant for air pruning

In the case of a plant grown in a conventional plastic pot, the roots roll up inside the plastic pot. The roots become excessively long as the plant continues to search for new areas of fertile substrate rather than developing branches. The roots will even come to protrude from the holes below the plastic pots. They will continue to grow below these unless controlled with open air.

Air pruning occurs naturally when the root tips come into contact with air. Instead of continuing to spread, the root tip dies, and more roots grow to create a fibrous mass. Instead of a few large and long spaghetti-like roots, plants that have had their root system controlled in contact with the air develop a root mass made up of a multitude of small roots wandering throughout the growing medium. By encouraging a dense root mass, in an oxygenated and well-drained medium, your plants will be able to assimilate more nutrient solutions and you won't have to worry about root rot. This will also result in better growth of stronger plants, and the end result will therefore be bigger harvests at the end of the cycle.